{"product_id":"concrete-drainboard-insert-mold-grill","title":"Concrete Drainboard Insert Mold - Grill","description":"\u003ch2\u003eConcrete Drainboard Insert Mold - Grill\u003cbr\u003e\n\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan style=\"font-style: italic;\"\u003e\u003c\/span\u003eMold Measurements:\n\u003cul\u003e\n\u003cli\u003e13 7\/8\" Wide (at sink)\u003c\/li\u003e\n\u003cli\u003e11 7\/8\" Wide (end opposite sink)\u003c\/li\u003e\n\u003cli\u003e17 15\/16\" Long\u003c\/li\u003e\n\u003cli\u003e1\/4\"-1\/2\" Sloped Height.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eRaised Slot Channels are 1\/2\" Wide, 1\/8\" High (at sink), 3\/8\" High (far end).\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-style: italic;\"\u003e*Occasional imperfections may be present on Rubber Molds, and can be removed or altered using a sharp utility knife, or a very abrasive sand paper or resin-bound grinding discs.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eConcrete Drainboard Insert Mold - Grill\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRubber Drain Board insert for use with concrete countertop fabrication.\u003c\/li\u003e\n\u003cli\u003eThe Grill Drainboard has 3 raised areas in the mold, which create recessed channels in the finished concrete.\u003c\/li\u003e\n\u003cli\u003eThe recessed channels can be left as drainage channels, or inserted with three 1\/2\" square bar stainless steel trivets:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003e 1\/2\" Stainless Trivets Sold Individually Here.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWhen 1\/2\" Stainless Steel Trivets are inserted into the finished drainboard, the top of the Trivets will be very close to level with the countertop surface, while the drainboard surface below them slopes towards the sink\u003c\/strong\u003e.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eClean, nice edges. Fast and simple to use. Add a professional drainboard to your countertop form in minutes.\u003c\/li\u003e\n\u003cli\u003eSeamless integral drainboard, countertop, and\/or sink.\u003c\/li\u003e\n\u003cli\u003eDrainboard slopes toward sink.\u003c\/li\u003e\n\u003cli\u003eIf the drainboard needs to be shaped (to meet flush with a specific sink), simply cut the rubber mold with a sharp razor knife, or fine tooth jigsaw blade.\u003c\/li\u003e\n\u003cli\u003eMade of extremely durable polyurethane that can flex and stay strong.\u003c\/li\u003e\n\u003cli\u003eCan be used in pre-cast or poured in place concrete work.\u003c\/li\u003e\n\u003cli\u003eFast and easy to place in a mold, and quick to clean after use.\u003c\/li\u003e\n\u003cli\u003eGood for hundreds of uses- Actually gets better with each use as they 'season'.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eConcrete Drainboard Insert Mold - Grill Setup:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePlace Drainboard Mold in your form and silicone in place.\u003c\/li\u003e\n\u003cli\u003eFor most applications (Precast), run a silicone a bead across the bottom edge of the Drainboard Mold to create a water-tight seal.\n\u003cul\u003e\n\u003cli\u003eIf using for poured in place concrete countertops, press the drainboard down into the concrete surface, lightly tapping until flush with the surface, and then place a board or 2x4's across the top of the concrete and Drainboard Mold to hold it in place while the concrete sets up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eUse of a Rubber Safe form release is recommended, and will create a smoother finish on the concrete, less air pockets, and make cleaning the rubber mold easier when finished.\u003c\/li\u003e\n\u003cli\u003eVibrate concrete well (either vibrating the concrete, or rapidly tapping the edges of the forms with a hammer or palm sander), to remove as many air pocket voids as possible.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eDrainboard Mold Removal:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAfter the concrete is sufficiently set up (typically 2-3 days for precast), flip the concrete piece over and remove the Drainboard Mold. In many cases, the mold will stay siliconed to the form when separated from the concrete.\u003c\/li\u003e\n\u003cli\u003eConcrete may have small 'bumps' which can be sanded off with a 200 grit sandpaper. These bumps tend to disappear the more the Rubber Drainboard Mold is used, as it becomes seasoned.\u003c\/li\u003e\n\u003cli\u003eFill any air pocket voids with a Concrete Slurry Mix.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eRubber Mold Care:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eClean with a stiff brush and water after each use. Any silicone left on the forms should be peeled or scraped off (the sooner the easier to remove). Any hardened concrete and difficult to remove silicone can usually be removed using a wire brush.\u003c\/li\u003e\n\u003cli\u003eMuriatic Acid can be used to clean of cement residue from the rubber mold in a 20:1 ratio (20 parts water to 1 part muriatic acid). Rub the Drainboard Mold with a stiff nylon brush and the muriatic acid water. Rinse the mold thoroughly with clean water.\u003c\/li\u003e\n\u003cli\u003eStore rubber molds out of direct sunlight, laid out flat.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ciframe width=\"600\" height=\"250\" src=\"https:\/\/www.youtube.com\/embed\/Bm_Hq6eIssc\" title=\"YouTube video player\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture\" allowfullscreen=\"\"\u003e\u003c\/iframe\u003e","brand":"PNL Liners","offers":[{"title":"Default Title","offer_id":46517458436153,"sku":"azq1789526539687","price":78.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0796\/9888\/6713\/files\/concrete-drainboard-insert-mold---grill_1.jpg?v=1789526567","url":"https:\/\/tonalstylingoutfit.shop\/products\/concrete-drainboard-insert-mold-grill","provider":"My Store","version":"1.0","type":"link"}