{"product_id":"concrete-mold-soap-dish","title":"Concrete Mold, Soap Dish","description":"\u003ch2\u003eConcrete Mold, Soap Dish\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eRubber Soap Dish insert for use with concrete countertop fabrication.\u003c\/li\u003e\n\u003cli\u003eFast and simple to use. Add a professional soap dish to your countertop form in minutes.\u003c\/li\u003e\n\u003cli\u003eReusable- Made of durable polyurethane that can flex and stay strong. Re-usable dozens or more times with proper care.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications- Concrete Mold, Soap Dish:\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAvailable in two thicknesses:\u003c\/li\u003e\n\u003cul\u003e\n\u003cli\u003eStandard size: 6\" Wide, 3\" long, 1\/2\" Thick\u003c\/li\u003e\n\u003cli\u003eThin size: 6\" Wide, 3\" long, 1\/4\" Thick\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cli\u003eThe three sides to the Soapdish Mold have a sloped angle to them, with the side that is designed to meet the sink being flat, so it can be placed right against the Sink Mold, or sink knockout piece.\u003c\/li\u003e\n\u003cli\u003eThe Soapdish Mold 4 depressed grooves in the Mold, which create raised channels in the finished concrete.\n\u003cul\u003e\n\u003cli\u003eGrooves add a visual element to the Soapdish, and allow water to drain off the soap bar.\u003c\/li\u003e\n\u003cli\u003eChannels are approx. 3\/16\" wide.\u003c\/li\u003e\n\u003cli\u003eThree of the channels are 5\" long, and one is 3 3\/4\" long.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eConcrete Mold, Soap Dish Setup:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePlace Soapdish Mold in your form and silicone in place.\u003c\/li\u003e\n\u003cli\u003eFor most applications (Precast), run a silicone a bead across the bottom edge of the mold to create a water-tight seal.\n\u003cul\u003e\n\u003cli\u003eIf using for poured in place concrete countertops, press the mold down into the concrete surface, lightly tapping until flush with the surface, and then place with 2x4's across the top of the concrete and mold to hold it in place while the concrete sets up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eUse of a Rubber Safe form release is recommended, but usually not necessary. Form release generally will create a smoother finish on the concrete, less air pockets, and make cleaning the rubber mold easier when finished.\u003c\/li\u003e\n\u003cli\u003eVibrate concrete well (either vibrating the concrete, or rapidly tapping the edges of the forms with a hammer or palm sander), to remove as many air pocket voids as possible.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMold Removal:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAfter the concrete is sufficiently set up (typically 2-3 days for precast), flip the concrete piece over and remove the mold. In many cases, the mold will stay siliconed to the form when separated from the concrete.\u003c\/li\u003e\n\u003cli\u003eConcrete may have small 'bumps' which can be sanded off with a 200 grit sandpaper.\u003c\/li\u003e\n\u003cli\u003eFill any air pocket voids with a Concrete Slurry Mix.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: bold;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003eRubber Mold Care:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eClean with a stiff brush and water after each use. Any silicone left on the forms should be peeled or scraped off (the sooner the easier to remove). Any hardened concrete and difficult to remove silicone can usually be removed using a wire brush.\u003c\/li\u003e\n\u003cli\u003eMuriatic Acid can be used to clean of cement residue from the rubber mold in a 20:1 ratio (20 parts water to 1 part muriatic acid). Rub the Edge Form Liner with a stiff nylon brush and the muriatic acid water. Rinse the mold thoroughly with clean water.\u003c\/li\u003e\n\u003cli\u003eStore rubber molds out of direct sunlight, laid out flat.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"PNL Liners","offers":[{"title":"Standard 1\/2\" Thick","offer_id":46517624832057,"sku":"gua1789529150110","price":16.14,"currency_code":"USD","in_stock":true},{"title":"Thin 1\/4\" Thick","offer_id":46517624864825,"sku":"adq1789529150111","price":14.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0796\/9888\/6713\/files\/concrete-mold-soap-dish_1.jpg?v=1789529153","url":"https:\/\/tonalstylingoutfit.shop\/products\/concrete-mold-soap-dish","provider":"My Store","version":"1.0","type":"link"}